The Seeed Studio XIAO MG24 is a tiny, low-power wireless development board based on the Silicon Labs EFR32MG24 SoC. It combines a modern 32-bit Arm Cortex-M33 processor with 2.4Â GHz wireless connectivity, making it a very interesting XIAO module for compact IoT, smart home, Matter, Thread, Bluetooth, and battery-powered projects.
Like all boards in the Seeed Studio XIAO family, the XIAO MG24 uses an ultra-compact 21 × 17.8 mm form factor while still providing a surprisingly rich set of GPIO and communication interfaces. It is breadboard-friendly, USB-C programmable, and small enough for embedded projects where a full-size development board would be too large.
The onboard Silicon Labs EFR32MG24 features a 78Â MHz Arm Cortex-M33 core with DSP instructions, floating-point support, and a built-in AI/ML hardware accelerator. This gives the module much more processing power than classic entry-level microcontroller boards while keeping power consumption very low.
The XIAO MG24 supports modern 2.4Â GHz wireless protocols including Matter over Thread, OpenThread, Zigbee, Bluetooth Low Energy 5.3, and Bluetooth mesh. This makes it especially useful for smart home devices, wireless sensors, battery-powered control nodes, and experimental Matter/Thread projects.
Key features
Silicon Labs EFR32MG24 wireless SoC
Arm Cortex-M33 32-bit processor, up to 78Â MHz
DSP instructions and floating-point support
Built-in AI/ML hardware accelerator
256Â KB RAM
1536Â KB internal Flash plus 4Â MB onboard Flash
2.4Â GHz wireless connectivity
Supports Matter over Thread, OpenThread, Zigbee, Bluetooth LE 5.3, and Bluetooth mesh
Up to +19.5Â dBm transmit power
Receiver sensitivity down to -105.4Â dBm
19 digital/analog-capable GPIO pins
PWM support on available GPIO pins
I²C, UART, and SPI interfaces
Hardware security features including cryptographic acceleration, true random number generator, Arm TrustZone, secure boot, and secure debug unlock
Onboard user LED and power LED
Reset button
USB-C connector for power and programming
Battery charging circuit for rechargeable 3.7Â V lithium battery projects
Ultra-compact XIAO form factor: approx. 21 × 17.8 mm
Technical specifications
MCU / SoC
Silicon Labs EFR32MG24
CPU
Arm Cortex-M33 32-bit processor, up to 78Â MHz
RAM
256Â KB
Flash
1536Â KB internal Flash + 4Â MB onboard Flash
Wireless
2.4Â GHz multi-protocol radio
Supported protocols
Matter over Thread, OpenThread, Zigbee, Bluetooth LE 5.3, Bluetooth mesh
GPIO
19 digital/analog-capable GPIO pins
PWM
Available on GPIO pins
Interfaces
I²C, 2× UART, 2× SPI
ADC
12-bit ADC, up to 1Â Msps
Security
Cryptographic acceleration, true random number generator, Arm TrustZone, secure boot, secure debug unlock
Antenna
Onboard 2.4Â GHz ceramic antenna
Typical low-power current
Approx. 1.95 µA
Typical sleep current
Approx. 1.91Â mA
Typical normal operating current
Approx. 6.71Â mA
Power input
5Â V via USB-C, or rechargeable 3.7Â V lithium battery via battery pads
Logic level
3.3Â V
Operating temperature
-20 °C to +70 °C
Dimensions
Approx. 21 × 17.8 mm
Important: The XIAO MG24 is a 3.3Â V logic device. Do not connect 5Â V signals directly to the GPIO pins.
This module can be used with our CANABLOX® development system. A suitable XIAO adapter board, such as CX-XIAO-S or CX-XIAO-MH, is required. It can also be added to our CANADUINO® PLC-300 V2 Programmable Logic Controller DIY kit to provide extended functionality and wireless connection.
For pinout, Arduino setup, battery usage, wireless examples, schematics, and additional documentation, please refer to the official Seeed Studio XIAO MG24 documentation: